Your cart is empty!
Select a category below to browse instruments
Categories
Browse Instruments
The fully threaded double‑ended K‑wire at 1.6mm carries trocar points on both ends of a 152mm shaft, with full thread length providing maximum fixation purchase against bone. The six‑per‑package format supports surgeon‑side selection during fracture fixation.
Features & Benefits
The fully threaded 1.6mm double‑ended K‑wire carries trocar points on both ends of a 152mm shaft, with full thread length giving maximum fixation purchase against cortical bone. The configuration supports fracture work where the wire must resist axial pull‑out.
Supplied sterile in individual packages, this double‑ended 0.9mm trocar‑point K‑wire meets clean field requirements for percutaneous metaphyseal fixation. The 152mm length and stainless‑steel construction enable reliable bone engagement during open or closed reduction workflows.
This double‑ended K‑wire features a trocar point geometry and 0.9mm diameter, ideal for percutaneous fixation across metaphyseal bone and articular surfaces. The 152mm length supports trajectory control through bone cortices while maintaining structural integrity for repeated insertion.
Sterile and individually packaged, this 1.1mm trocar‑point K‑wire meets rigorous clean field protocols for open reduction and percutaneous techniques. The 152mm length and double‑ended configuration support efficient bone positioning during acute trauma and elective procedures.
With increased 1.1mm diameter and trocar point, this double‑ended K‑wire addresses larger bone purchase and load-bearing anatomy. The 152mm length maintains maneuverability while the stainless‑steel construction withstands repeated insertion and positioning cycles.
This individually sterile‑packaged variant of the 1.1mm trocar‑point K‑wire prioritizes case‑to‑case sterility assurance for percutaneous pin application. The 152mm straight shaft enables precise alignment through metaphyseal and diaphyseal bone during open and closed techniques.
The 1.4mm diameter variant supplies maximum trocar‑point penetration capacity for heavy cortical engagement in trauma and revision work. Packaged sterile in groups of six with individual component assurance, this K‑wire supports reliable bone capture at 152mm length.
Sterile packaged with 1.6mm diameter and trocar point geometry, this K‑wire addresses the largest bone fixation demands in trauma and reconstruction. The 152mm straight shaft maintains precision while supporting reliable ancillary fixation across load‑bearing anatomy.
The largest 1.6mm diameter variant in this K‑wire series offers maximum bone grip for load‑bearing applications in metaphyseal and diaphyseal zones. The trocar point provides reliable cortical penetration at the 152mm working length, supported by reusable stainless‑steel construction.
Built at 0.7mm (0.028") shaft diameter, this double‑ended K‑wire carries trocar points on a 305mm body for the finest percutaneous fixation work. The fine gauge suits small‑fragment fixation in hand and foot surgery where minimal cortical disturbance is wanted.
The 0.7mm K‑wire with double trocar points duplicates the finest standard gauge wire for instrument sets requiring multiple K‑wires across the case. The double‑ended format doubles usable length per pin.
The 0.7mm K‑wire with double trocar points delivers the finest standard percutaneous fixation gauge at extended working length, suited to delicate hand and small‑bone fixation where minimal cortical disturbance is wanted.
This double‑ended 0.7mm K‑wire at 229mm bridges the compact and extra‑long formats, suited to small‑fragment fixation where the surgeon needs more working length than the 102mm variant but less than the 305mm. The fine gauge minimizes cortical disturbance.
The double‑ended K‑wire variant carries trocar points on both ends of a 305mm (12") 0.9mm (0.035") shaft, doubling usable length per pin during long‑bone or external‑fixation cases. The non‑sterile five‑per‑package format suits surgeon‑side cutting to length during the procedure.
The 0.9mm K‑wire with double trocar points on a long shaft delivers fixation of small and medium fragments at extended working length. The trocar geometry drives through cortical bone on both ends, and the standard gauge suits routine percutaneous fixation.
The 0.9mm K‑wire with double trocar points duplicates the standard gauge variant for instrument sets requiring multiple K‑wires across the case. The double‑ended format doubles usable length per pin during percutaneous fixation work.
Built at 1.1mm with double‑ended trocar points on a 152mm shaft, this K‑wire pairs the intermediate gauge with the double‑ended format for fixation work needing more usable length than the compact 102mm version. The trocar geometry suits direct cortical entry on both ends.
The 1.1mm K‑wire with double trocar points on a longer shaft delivers intermediate‑gauge fixation at extended working length, where the surgeon needs more reach than the compact 102mm variant. The trocar geometry drives cleanly through cortical bone.
This 1.1mm double‑ended K‑wire on a longer shaft pairs the intermediate gauge with extended working length, suited to long‑bone applications where additional reach is wanted at the same shaft stiffness. The trocar geometry drives through cortical bone on both ends.
Built at 1.4mm (0.054") shaft diameter, this double‑ended K‑wire bridges the 0.9mm and 1.6mm standard sizes for fixation work that needs more stiffness than the fine wires but less mass than the heavy variants. The 305mm length suits long‑bone applications.
Sized at 1.4mm with trocar points on both ends of a 305mm shaft, this double‑ended K‑wire bridges the 0.9mm and 1.6mm standard sizes for intermediate‑gauge fixation work at extended length. The longer body suits long‑bone applications and external fixation frames.
Sized at 1.4mm with double trocar points, this K‑wire bridges the 0.9mm and 1.6mm standard gauges for fixation work needing intermediate shaft stiffness. The double‑ended format doubles usable length per pin during long‑bone and external‑fixation cases.
Stepping up to 1.6mm (0.062") in diameter, this double‑ended K‑wire variant adds shaft stiffness for fixation of larger bone fragments and external frames. The 305mm length and double trocar tips allow the surgeon to cut a fresh length from the unused end during the case.
This 1.6mm K‑wire with double‑ended trocar points on a compact 102mm shaft provides percutaneous fixation of larger bone fragments where the surgeon wants more usable length than a single‑ended format. The heavier shaft stiffness suits hand and foot work with substantial fragments.
Sized at 1.6mm with double trocar points on the standard long shaft, this K‑wire provides heavy‑gauge fixation at extended working length for larger‑fragment percutaneous work where the surgeon needs maximum reach.
This partially threaded double‑ended K‑wire carries trocar points on both ends of a 1.6mm × 152mm shaft, with the threaded section providing fixation purchase against bone. The 12‑per‑package format supports surgeon‑side selection during fracture and fixation cases.
This 0.7mm K‑wire with a single diamond point delivers fine percutaneous fixation through dense cortical bone, where the diamond geometry cuts more cleanly than the trocar variant at the smallest standard gauge. The single‑ended format suits one‑direction insertion.
Built at 1.1mm with a single diamond point, this K‑wire combines intermediate shaft stiffness with the sharper drilling geometry of the diamond tip, sized for fixation work where the wire must drill through dense cortical bone in a single direction.
Swapping the trocar for a diamond point, this 1.4mm (0.054") Kirschner wire reduces drilling deflection on hard cortical bone and dense fixation sites. The 230mm straight shaft drives the wire deep into long bone or across multiple fragments, and the single‑ended geometry seats cleanly into drill chucks. Supplied non‑sterile, five per package, with disposable stainless steel construction.
Our sales specialists are available Monday through Friday, 9am to 5pm EST.