Your cart is empty!
The Henderson Limbal Relaxation Marker is engineered for surgical planning during Limbal Relaxing Incision (LRI) procedures, marking 30, 60, and 90 degree axis points on the cornea for precise incision placement. The marker pairs with the Henderson bevel degree gauge for reproducible astigmatism correction. Stainless steel construction maintains dimensional consistency across repeated reprocessing cycles.
Features & Benefits
This Henderson pre‑operative reference marker uses a durable half‑circle geometry with blunt positioning pins at 0�, 90�, and 180�. The round knurled handle improves grip security during toric axis pre‑marking while minimizing rotational drift.
This Henderson toric IOL marker creates two 2.5mm radial marks that extend to 11mm, enabling clear visualization of planned lens orientation. Its balanced design ensures smooth rotational control across the corneal surface.
The Hoffer O-Z Marker with 3.75mm diameter provides precision optical zone demarcation for refractive surgery. Its etched extra‑fine crosshairs enable dual‑axis visualization to confirm visual axis alignment, while the symmetric ring footprint creates a repeatable reference for corneal ablation. The flat smooth handle permits single‑hand contact marking, and the 100mm overall length maintains clear visibility during setup.
Built around a 3mm marking ring crossed by extra‑fine cross hairs, the Hoffer O‑Z marker stamps both an optical‑zone outline and a centration reference in a single press. The flat smooth handle on the 102mm straight stainless‑steel shaft delivers a stable thumb purchase as the surgeon registers the cross hairs to the visual axis.
The Hoffer O-Z Marker with 4.25mm diameter is engineered for slightly larger optical zones in refractive surgery planning. Its extra‑fine etched crosshairs provide dual‑axis visual reference to ensure precise centration relative to the pupil and visual axis. The flat smooth handle and 100mm shaft allow single‑hand positioning without interference with patient setup, supporting rapid and accurate marking during preoperative planning.
The Hoffer O-Z Marker with 4.75mm diameter accommodates the largest optical zone variations in refractive and post‑refractive procedures. Its extra‑fine etched crosshairs support precise centration during marking, enabling surgeon verification of visual axis alignment before excimer laser application. The flat smooth 100mm handle ensures steady single‑hand contact without corneal adhesion.
This Hoffer O‑Z marker uses the same 4mm calibrated marking diameter with extra‑fine crosshairs but incorporates a round knurled handle for enhanced rotational grip during O‑Z centration alignment.
This Hoffer O‑Z marker features a 4mm circular marking diameter with extra‑fine crosshairs for precise centration. The smooth flat handle provides steady axial control, and the compact 100mm length supports stable corneal reference marking.
Optical zone precision during refractive and cataract procedures is supported by the Hoffer O?Z marker with extra?fine cross hairs and 5.25mm diameter. The fine crosshair pattern enables accurate center identification and concentric zone definition. Its 102mm round handle supports sensitive control during critical marking steps.
Designed for toric IOL alignment and refractive marking, this Hoffer O‑Z marker stamps a 5.5mm optical zone with extra‑fine crosshairs onto the corneal surface. The crisp engraved pattern transfers cleanly to gentian violet ink, defining the visual axis for centration and astigmatic axis steps. A smooth flat handle anchors the marker square to the cornea.
This Hoffer O‑Z marker provides a 5.75mm circular marking zone with extra‑fine crosshairs for enlarged O‑Z reference definition. The round handle supports uniform downward pressure for consistent placement.
This Hoffer O‑Z marker incorporates a 5mm diameter marking face with extra‑fine crosshairs. The round knurled handle improves tactile precision and micro‑control during centration marking.
This Hoffer O‑Z marker features a 6mm circular marking diameter with extra‑fine crosshairs. The smooth flat handle enhances fingertip stability across the 110mm instrument length.
Larger optical zones in refractive marking and implant planning benefit from the Hoffer O?Z marker in its 7.5mm configuration. Extra?fine cross hairs ensure accurate axis alignment, while the 110mm flat smooth handle provides stable control during extended marking procedures.
The Hoffer O-Z marker features extra-fine crosshairs etched within a 7mm diameter ring to guide surgeons in achieving precise rotational alignment during toric IOL implantation. The smooth flat handle enables steady corneal contact. At 108mm, optimal length facilitates single-handed marking and pupillary positioning.
This Hoffer O‑Z marker incorporates an 8.5mm diameter marking ring with extra‑fine crosshairs for large‑zone centration. The round knurled handle ensures stable rotational traction across its 110mm length.
This Hoffer O-Z marker's 8mm diameter ring with extra-fine crosshairs provides enhanced reference geometry for precise astigmatism axis alignment and toric IOL implantation. The smooth flat handle maintains steady corneal positioning. At 108mm, optimal length facilitates controlled marking without hand tremor.
This Hoffer O‑Z marker offers a 9mm calibrated marking diameter with extra‑fine crosshairs. The round knurled handle enhances controlled placement during wide‑zone corneal marking.
Larger than its 5.5mm counterpart, this 9mm Hoffer O‑Z marker prints a wider optical zone with extra‑fine crosshairs for refractive planning and toric IOL alignment. The broader ring suits eyes with larger mesopic pupils, while the engraved crosshairs transfer crisply to gentian violet. A smooth flat handle steadies the stamp during application.
This Hoffer optical zone marker is calibrated with cross‑hair alignment and a 3.5mm ring height for reproducible refractive surgery marking. The beveled 3mm tip seats cleanly against the corneal surface and marks a concentric zone for IOL power calculation and LASIK optical zone planning. A round knurled handle and dull finish provide stable, ergonomic control.
The Hoffer optical zone marker's cross-hair pattern enables precise centration of laser ablation zones during LASIK procedures. The 5.75mm ring height accommodates varied anterior segment anatomy while supporting repeatable reference marking patterns.
This Hoffer optical zone marker is scaled to a 6mm marking diameter for larger refractive optical zones and IOL power calculations in LASIK, refractive cataract, and implant surgery. Cross‑hair alignment ensures accurate centering on the visual axis. The compact 93mm length and knurled grip support precise intraoperative positioning.
This Hoffer optical zone marker features a 7mm marking diameter and cross‑hair alignment for larger refractive zones in advanced cataract and corneal refractive procedures. The 3mm ring height and beveled tip allow crisp marking across variable corneal topography. A round knurled handle and 115mm length support stable positioning during LASIK and toric IOL alignment.
This intra‑operative toric axis marker, titanium, features a 13.5mm outer diameter, 10.5mm inner marks, and a rotatable axis marker aligned at 90 degrees for toric reference marking.
The intrascleral haptic marker and Yamane double needle stabilizer work together to localize and mark haptic position during ab interno IOL fixation procedures. The stainless‑steel instrument marks the sclera at planned fixation sites and stabilizes the double needle technique during sutureless intraocular lens implantation. This specialized tool supports emerging techniques in aphakic and IOL repositioning cases.
The Lindstrom accurate marker places a 7mm reference impression on the cornea to guide centration of refractive incisions and intraocular procedures. A smooth flat handle on a 100mm shaft supports a balanced perpendicular approach to the corneal surface, transferring a clean uniform mark.
This Gills‑Nomogram LRI marker provides precise peripheral corneal marking for limbal relaxing incision planning. The 0 to 180 degrees etched head allows accurate axis alignment, while the 6 and 8mm cord lengths correspond to standard Gills‑nomogram incision arcs. The titanium body offers lightweight rigidity and withstands repeated sterilization.
This LRI (limbal relaxing incision) marker embodies the Nichamin nomogram with precise etch markings for 40, 60, and 80‑degree astigmatism correction zones. The 0‑to‑180‑degree etched head supports accurate axis alignment during incisional astigmatism correction. Its 122mm titanium construction delivers reliable marking precision over many cases.